SKU: SKU: T417 20 Gladiator BLK/BLK - OG F&R
Earn [points_amount] when you buy this item.
Please factor in 6-14 Business Days for Processing and Assembly.
WHAT'S INCLUDED:
Each full kit comes with 4 flaps (front and rear), heavy-duty powder coated steel brackets for the rear, a complete kit of stainless steel and rust-resistant mounting hardware, and installation instructions to fit factory hole locations.
WHAT IT FITS:
2020+ Jeep Gladiator (JT)
Most trim levels including Rubicon, Mojave, Willys etc.
Designed on the RUBICON fenders but will also fit the Sport, Sport S and any other non Rubicon fenders with a tiny bit of trimming (SEE FAQ BELOW)
DOESN'T FIT:
High Altitude Trim
Aftermarket or SPLIT/Modified OEM FENDERS
Any other Jeep Model
Some Non USDM models may have slight differences
4 SIZES TO CHOOSE FROM:
-ORIGINAL was designed for those who like to keep a stock set up, but want some paint protection. This size is good for stock tires up to about 34 inches.
-ORIGINAL LONG is the same width, but adds about 2" on the bottom edge for those who don't need/want the added width of XL but want maximum protection from wheel spray.
-XL is about 1-2" wider and 1-2" longer for those who run lifts and/or higher offset wheels that poke past the fenders.This size is good for tires from about 35 inches up to about 40 inches.
-XL LONG is the same width, but adds about 2" on the bottom edge for those who want maximum protection.
***PHOTOS SHOW THE XL SIZE.
Please note that this kit was designed on a stock USDM vehicle. When modifying body panels, wheels or suspension, you may have to modify the flaps to work with those changes. If you have any questions before you purchase, please see our FAQ below or email us with any questions.
COLOR OPTIONS:
Rokblokz Mud Flaps are available in BLACK, RED, YELLOW, GREY, DEEP BLUE, BRIGHT BLUE, ORANGE, LIME GREEN, OLIVE DRAB, and DEEP PURPLE. Colors other than Black are considered Custom as they are made to order.
*NO RETURNS ON COLORED FLAPS
Screen resolution, lighting, and surroundings all affect how colors present. If you are questioning how well the color will match, please order a set of sample colors HERE.
Please note that a shopping cart quantity of 1 refers to the number of kits you are selecting not the number of flaps. In this listing, you are purchasing 4 mud flaps and all accompanying hardware and brackets.
**Please note that aftermarket exhaust could affect the mounting of the rear brackets.**
You may also request the front flaps without the partial hole cut out if you either don't have the OEM Rubicon Rock Sliders and/or need to modify the flaps yourself for other rock sliders/side steps. Just make sure to leave a NOTE when ordering saying "NO PARTIALLY CUT HOLE PLEASE".
RokBlokz Quick Release mud flaps for the 2020+ Jeep Gladiator (JT) mud flaps are CNC laser cut from a proprietary material specifically designed to endure the harshest environments from extremely hot climates to extremely cold ones. They offer excellent protection from harsh road debris and gravel. The Gladiator (JT) kit fits all trim levels including the Sport, mid-level Sport S, luxurious Overland, the off-road-ready Rubicon and Mojave, as well as the Launch Edition.
The unique blend of polymers in our mud flaps gives them the specific ability to remain rigid enough to not flap in the wind, flexible enough to bend and give over obstacles, and durable enough to take whatever abuse you can throw at them. Rokblokz mud flaps can bend, flex, give, even scrape and drag without breakage.
If you are having a hard time getting the front flaps to line up (especially with the Rubicon rock rails) please watch this short clip for extra details on how to tilt and slide the flap into place.
 If you have a 2023 Mode with the 3rd tab on the fender liner bracket, you will need to make sure that the flap sits behind to two outer tabs (marked in green on the photo) and in front of the 3rd center tab (circled in red on the photo). Alternately you can place the clips on the two outer tabs with the extruded side pointing toward the center tab, rather than your flap and mount the flap on top of the fender liner. When mounting this way, you may want to add a fender washer between the thumb screw and the flap.
Mounting is the same on non-Rubicon fenders including Sport and Tow Max Fenders, however, there are a couple of additional steps to make everything play nice. First as shown in the video and photo below there are a couple of places on the fender liner that will need to be trimmed. 1.) The lip on the liner will need to be trimmed a bit so the flap can sit properly. 2.) This is optional. If you want to be able to adjust your flap in and out, you will need to cut a slot in the fender liner. Please see short video below for details.
The FRONT FLAPS work with the OEM fenders ONLY. They will not mount on aftermarket fenders, modified or SPLIT OEM fenders.
The REAR FLAPS are mounted using a heavy-duty powder-coated steel bracket that is mounted to the frame so they are unaffected by modifying the fenders or running aftermarket fenders.
They are designed with the shape of the OEM Rubicon Rock Rails partially cut out, simply cut the tabs and remove the shape allowing the Rubicon Rock Rails to pass through the front flap.
Many other rock rails/side steps do not come as far forward as the OEM Rubicon sliders do and will not interfere with our mud flaps. See pics for more details. If you have the MOPAR PERFORMANCE RAILS you will either need to extend the pre-designed hole or cut your own hole as those are not the same as the stock rubicon rails.
You may also request the front flaps without the partial hole cut out if you either don't have the OEM Rubicon Rock Sliders and/or need to modify the flaps yourself for other rock sliders/side steps. Just make sure to leave a NOTE when ordering saying "NO PARTIALLY CUT HOLE PLEASE".
TheREAR FLAPS are mounted using a heavy-duty powder-coated steel bracket that is mounted to the Frame so they are unaffected by running aftermarket bumpers.
The REAR FLAPS are mounted to a heavy-duty powder-coated steel bracket that mounts directly to the Frame of the Vehicle. This bracket makes it possible to adjust the flaps in and out to account for a range of tire size and wheel offset. Because of this bracket system, you can easily remove the flaps without any tools right on the side of a trail if needed.
This listing is for the 2020+ Jeep Gladiator JT only. This kit will not work for the wrangler but will work on all Gladiator trims including the Sport, mid-level Sport S, luxurious Overland, the off-road-ready Rubicon and Mojave, as well as the Launch Edition. It will also work with the Eco Diesel model with stock exhaust. ***Sport and Max Tow Fenders will require a lip on the fender liner to be trimmed for proper mounting of the Flaps.
Front ONLY and Rear ONLY Kits are available HERE (they come with ONLY the 2 front flaps or the 2 rear flaps along with all mounting hardware, brackets, and installation instructions).
Yes, but the pricing will be different than a whole kit in the same size. You will have to go to the individual front or rear listing and add the desired size to your cart on each listing.